WetterCubePlus/Einstellungen/en
Settings can be changed in two places: the web interface (http://wettercubeplus.local) and directly on the menu screen of the display (gear icon on the main screen).
Web interface
The web interface has four tabs. The chosen tab stays when you reload and can be opened by link (e.g. http://wettercubeplus.local/#system). At the top right you switch between the light and dark design (without a choice your browser setting applies). On the Anzeige and Wetter & Daten tabs "Einstellungen speichern" (save settings) stays visible at the bottom, and a note shows unsaved changes.
| Tab | Card | Setting |
|---|---|---|
| Anzeige (display) | Display | Brightness 10–100 % (slider), dim timeout: off / 1 / 3 / 5 / 10 minutes |
| Night mode | Switch, from/to (15-minute steps), own night brightness 0–50 % | |
| Main screen | "Rechtes Feld" (right-hand field): shows pollen (your allergens) or biowetter (your four categories), the two strongest values. "Regenbalken im Temperaturverlauf" (rain bars in the temperature chart) on/off | |
| Hint tile | Rain, storm, frost and UV hint each on/off (default: all on) | |
| Wetter & Daten (weather & data) | Location & region | City (without umlauts) and DWD pollen region (federal state for warnings and radar map) |
| Warnings | Pollen warning on/off, DWD weather warnings on/off, pollen warning threshold: low / medium / high / strong | |
| My allergens | Switches for hazel, alder, ash, birch, grass, rye, mugwort, ragweed: the pollen warning, the health screen and the two pollen on the main screen consider only the selected ones | |
| Biowetter | DWD zone (A–K); weather sensitivity: 4 categories for the health screen | |
| Ampel (traffic light) | Traffic-light configuration | Mode (temperature / pollen / air quality) and temperature ranges for green/yellow/red of the WetterAmpel, with live display of what the light currently shows |
| System | Firmware update | Check for updates, show version and install (see Updates); "Log ansehen" opens the diagnostic log |
| Settings backup | "Einstellungen herunterladen" saves all settings as a file (without the Wi-Fi password); "Wiederherstellen" restores such a file and restarts the device | |
| Wi-Fi | "WLAN ändern" to enter new credentials |
Menu screen on the display
| Element | Function |
|---|---|
| Brightness slider | sets and saves the brightness directly |
| Pollen warning / DWD warnings switches | turn the respective warning on or off |
| "Bio statt Pollen" switch | right-hand field of the main screen: show biowetter instead of pollen |
| Light/dark switch | toggles between the light and dark color theme |
| Game icon | starts Bubblebreaker |
| Calculator icon | opens the calculator |
| Version label | shows the installed firmware version |
Defaults (after a fresh install that erased the flash)
| Setting | Default |
|---|---|
| Brightness | 80 % |
| Dim timeout | 3 minutes |
| Night mode | off (22:00 to 06:00, night brightness 10 %) |
| Pollen warning | on |
| Allergens | all eight selected |
| Traffic light | green 15–19 °C, yellow 20–24 °C, red 25–99 °C |
| Biowetter zone | A |
All settings are kept across firmware updates. They are only lost when the entire flash is erased (e.g. "erase device" in the web installer or "Erase All Flash" in the Arduino IDE). Tip: first use Einstellungen herunterladen in the web interface; afterwards Wiederherstellen brings them back (only the Wi-Fi has to be set up again).